 |
|
|
| |
|
Re-engineered to improve accuracy, reliability of operation and increase output, the Hydrotherm has the highest quality components and construction materials in the industry.
The Hydrotherm surpasses all competitive systems by providing stainless steel as the main component for wetted surfaces. Where many of our competitors supply carbon steel and cast iron systems, only Mokon provides the Hydrotherm with stainless steel components including a stainless steel pump, heater canister and pump suction manifold.
The Hydrotherm meets NFPA 79 (National Fire Protection Association) electrical standards and comes standard with a UL labeled electrical sub-panel. All of these features and more, combined with our extended warranty, make the Hydrotherm an easy choice for delivering precise temperature control.
|
| Model |
Pump |
Flow Rate & Pressure |
Cabinet Dimensions(LxWxH)*
3kW 6kW 9kW 12kW |
Cabinet Dimensions(LxWxH)*
18 kW 24 kW |
Process
Connection |
Supply/Drain |
| HZ |
1/2 hp |
15 gpm @ 15 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
| HY |
3/4 hp |
25 gpm @ 26 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
| HX |
1 hp |
30 gpm @ 32 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
| HR |
1-1/2 hp |
40 gpm @ 32 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
| HW |
2 hp |
50 gpm @ 32 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
| HN |
3 hp |
60 gpm @ 34 PSI |
27" x 11" x 24" |
27" x 16" x 25" |
1.25" NPT |
1/2" NPT |
|
| |
* 208 and 230 voltage rated 12 kW units are built in a 16" wide cabinet.
Multiple options may dictate a larger cabinet size. Contact Mokon for details.
|
To determine the Three (3) Phase full load amperage (FLA) look up the motor HP and Heater kW amperages based on the supplied voltage.
ie: 460 volts supplied voltage with 3/4 Hp motor and 9kW heater = 1.4 + 11.3 = 14.7 FLA.
|
| Motor HP |
208v |
230v |
380v |
460v |
575v |
|
Heater kW |
208v |
230v |
380v |
460v |
575v |
| 1/2 |
1.9 amp |
2.0 amp |
1.2 amp |
1.0 amp |
1.0 amp |
|
3 |
13.5 amp |
11.3 amp |
7.1 amp |
6.5 amp |
5.7 amp |
| 3/4 |
2.6 amp |
2.8 amp |
1.5 amp |
1.4 amp |
1.1 amp |
|
6 |
27.0 amp |
22.6 amp |
12.3 amp |
11.3 amp |
9.9 amp |
| 1 |
3.1 amp |
3.2 amp |
2.1 amp |
1.6 amp |
1.3 amp |
|
9 |
27.0 amp |
22.6 amp |
12.3 amp |
11.3 amp |
9.9 amp |
| 1 1/2 |
5.1 amp |
4.6 amp |
2.5 amp |
2.3 amp |
1.8 amp |
|
12 |
42.6 amp |
35.6 amp |
19.4 amp |
17.8 amp |
15.6 amp |
| 2 |
5.7 amp |
5.3 amp |
3.5 amp |
2.7 amp |
2.0 amp |
|
18 |
50.0 amp |
45.2 amp |
27.4 amp |
22.6 amp |
18.1 amp |
| 3 |
8.9 amp |
8.4 amp |
N/A |
4.2 amp |
3.1 amp |
|
24 |
66.6 amp |
60.2 amp |
36.5 amp |
30.1 amp |
24.1 amp |
|
|
 |
 |
| Standard Features |
| A• |
Hybrid-epoxy powder coated cabinetry (14 ga. base/16 ga. electrical enclosure) |
| B• |
Microprocessor-based controller in easily accessible control panel |
| C• |
Suction and discharge pressure gauges |
| D• |
High temperature safety shut-off switch |
| E• |
Pressure relief valve |
| F• |
Horizontal stainless steel heater canister |
| G• |
Copper heating elements mounted in back of canister for easy access |
| H• |
Low pressure safety shut-off switch |
| I• |
Solenoid cooling valve |
| J• |
Stainless steel pump |
| K• |
Casters for easy portability |
| L• |
Automatic air purge (not shown) |
| M• |
NFPA 79 and UL labeled electrical sub-panel (not shown) |
|
|
| |
| * Please consult factory for more information. |
|
|
|
Other Options Available:
|
| • |
Alarms |
| • |
All brass pump |
| • |
Closed water circuitry |
| • |
Control options |
| • |
Cooling or chilled circuits |
| • |
Door disconnect switch |
| • |
Emergency "crash" cooling control |
| • |
Flo-director |
| • |
Heat exchangers |
| • |
Heat remover design |
| • |
High/low heater operation (manual or automatic) |
| • |
Manifolds |
| • |
Modulating valves |
| • |
NEMA 4,12, and hazardous area ratings |
| • |
Other voltages, phases, frequencies |
| • |
Pressure regulators |
| • |
Solid state contactors/relays |
| • |
Stainless steel cabinets and components |
| • |
Tanks |
| • |
T.E.F.C. motor |
|
| * Other options available — see literature or consult factory for more information. |
| |
| Features of Standard and Optional Controls |
A variety of controls are available from Mokon to enhance the high performance of our systems. From solid state to microprocessor based, with communication capabilities to PLC type controls, Mokon can provide the type of control package right for your process.
|
| Eurotherm 3216 Series |
The Eurotherm 1/16 DIN (3216) microprocessor controller is now standard on the entire line of portable chillers, water and heat transfer fluid temperature control systems. This controller is operator friendly and easy-to-use. Standard features include a microprocessor PID controller for the highest accuracy in temperature control, a dual LCD display that shows set point and actual fluid temperature, and advanced PID overshoot protection with self-tuning capabilities for increased accuracy. Scrolling text messages deliver plain language messages to let users know exactly what is happening to the process.
There are optional 1/8 or 1/4 DIN controllers available, with high/low deviation alarm, remote set point and retransmission and serial communication. A five-year warranty comes standard with the controller. |
 |
|
| Custom Controls |
| Mokon’s ability to meet customers’ specific requirements is seen not only in custom system designs, but also in controls. Our engineers can custom design a control package that meets your specific processing needs, from brand name controls, to direct computer/host machine interfacing. All of which can be expected with the same quality and durability that our customers expect from our complete line of temperature control systems. |
|
| |